2008 Victory Hammer Specifications

Custom / cruiser • Specs last verified 13 July 2026

No images available
Tap to enlarge

2008 Victory Hammer Overview

For 2008, Victory offers the Hammer as a custom / cruiser motorcycle with 1634 cc on tap. The 2008 Victory Hammer is built around a Four stroke, 50° V twin SOHC, 4 valves per cylinder engine, a compression ratio of 9.8:1. In everyday use, the 2008 Hammer tips the scales at 305 kg, carries a 17-litre fuel tank, offers a seat height of 660 mm and spans a 1669 mm wheelbase. Every technical detail, from suspension travel to tyre sizes, is covered in the full 2008 Victory Hammer spec sheet below.

2008 Hammer - Pros & Cons

Strengths

  • Fuel injection: No choke, no jetting, no altitude compensation to think about - fuel injection just works across a wider range of conditions than carburetion.
  • Accessible seat height: At just 660 mm, flat-footing at a stop is easy for most riders - a genuine confidence builder for less experienced owners.
  • Low-maintenance final drive: Carbon Fiber Reinforced Belt final drive is about as close to maintenance-free as motorcycle drivetrains get.

Considerations

  • Age-related wear: No particular mechanical concern flags for the Hammer - condition on any used example comes down to how well it's been looked after.

Wear Points & Servicing Notes

Heat management in traffic

Air cooling on the Hammer keeps the mechanical layout simple, but heat management in slow traffic needs more attention than on a liquid-cooled bike - plan routes and gear accordingly in warmer conditions.

Fuelling & injector care

Fuelling on the Hammer comes from fuel injectionwith 44mm throttle bodies. Cold starts and throttle response stay consistent across altitude and temperature, the main practical edge over a carbureted equivalent.

Suspension condition on used examples

Suspension duties are handled by 43mm Inverted cartridge telescopic fork up front and Single, mono-tube gas forged and cast aluminum w/ rising-rate linkage at the rear. Weeping fork seals aren't a dealbreaker on a used bike, but they're a fair basis for negotiating price.

Final drive maintenance

Belt final drive keeps day-to-day maintenance minimal on the Hammer - just periodic tension and wear checks rather than the regular cleaning a chain demands.

Handling the weight at a standstill

The Hammer's 305 kg kerb weight is worth factoring into how you handle it at a standstill - parking-lot manoeuvres need a bit more deliberate technique than on a lighter machine.

Hammer - Buying & Maintenance Guide

What to check before buying

A pre-purchase check on the 2008 Victory Hammer should cover the same ground every time: service history, chain and sprocket condition, and any oil seepage around the casings. Start it from cold if you can - a well-kept Hammer settles to a smooth idle within seconds.

Oil and filter changes

Oil changes are the cheapest insurance you can buy for a Hammer's engine - keep to the manufacturer's interval rather than stretching it. Use the viscosity grade the manual specifies, not whatever's on sale.

Fuel system care

Injector systems like the Hammer's hold up well with basic care - decent fuel, an occasional cleaner additive, and draining old fuel before any layup longer than three months.

2008 Victory Hammer - Frequently Asked Questions

What engine does the 2008 Victory Hammer have?
The 2008 Victory Hammer uses a Four stroke, 50° V twin SOHC, 4 valves per cylinder engine with 1634 cc of displacement. It is air / oil.
How much does the 2008 Victory Hammer weigh?
The 2008 Victory Hammer weighs 305 kg. This is the manufacturer's dry figure.
What is the fuel tank capacity of the 2008 Victory Hammer?
The 2008 Victory Hammer has a 17-litre fuel tank. At around 5-6 litres per 100 km, that is roughly 283-340 km between stops.
Is the 2008 Victory Hammer suitable for shorter riders?
The 2008 Victory Hammer has a seat height of 660 mm. This is a comfortable, accessible height for most riders.
What brakes does the 2008 Victory Hammer have?
The 2008 Victory Hammer uses 2x 300mm floating rotor 4 piston caliper at the front and Single 300mm floating rotor 2 piston caliper at the rear.
What tyre sizes does the 2008 Victory Hammer use?
The 2008 Victory Hammer runs 130/70 R18 front and 250/40 R18 rear tyres. A good selection of sport, touring and all-weather rubber is available in these sizes.
What gearbox does the 2008 Victory Hammer have?
The 2008 Victory Hammer is fitted with a 6 Speed transmission.

Key Specifications

Engine

Four stroke, 50° V twin SOHC, 4 valves per cylinder

Power

Not published by manufacturer

Torque

Not published by manufacturer

Top Speed

Not published by manufacturer

Weight

305 kg / 672 lbs

Fuel Capacity

17 Litres / 4.5 US gal

Advertisement

Full 2008 Victory Hammer Specifications

Year 2007 - 08
Make Model Victory Hammer
Seat Height 660 mm / 26 in
Wheelbase 1669 mm / 65.7 in
Ground Clearance 135 mm / 5.3 in
Length 2366 mm / 93.1 in
Dry Weight 305 kg / 672 lbs
Fuel Capacity 17 Litres / 4.5 US gal
Displacement 1634 cc / 100 cu-in
Engine Detail Four stroke, 50° V twin SOHC, 4 valves per cylinder
Bore x Stroke 101 x 102 mm
Compression Ratio 9.8:1
Cooling System Air / oil
Fuel Induction Electronic Fuel Injection with 44mm throttle bodies
Starter Electric
Battery Capacity 12 volts / 18 amp hours
Clutch Wet, multi-plate
Final Drive Carbon Fiber Reinforced Belt
Transmission / Drive 6 Speed
Suspension - Front 43mm Inverted cartridge telescopic fork
Suspension - Rear Single, mono-tube gas forged and cast aluminum w/ rising-rate linkage
Rake 32.7°
Trail 140 mm / 5.5 in
Wheel Travel - Front 130 mm / 5.1 in
Wheel Travel - Rear 100 mm / 3.9 in
Brakes - Front 2x 300mm floating rotor 4 piston caliper
Brakes - Rear Single 300mm floating rotor 2 piston caliper
Tyres - Front 130/70 R18
Tyres - Rear 250/40 R18
Wheels - Front 18 x 3.5 in
Wheels - Rear 18 x 8.5 in

Specifications are compiled from manufacturer documentation and cross-referenced technical sources, and corrected on an ongoing basis. Spot an error? Let us know.

Advertisement

Victory Hammer - other years