![]()
No images available
Tap to enlarge
![]()
2024 Honda NX 500 Overview
The 2024 Honda NX 500 is an enduro / off-road motorcycle built around 471 cc of displacement. Under the tank sits a Four stroke, parallel-twin, DOHC, 4 valves per cylinder engine, a compression ratio of 10.7:1. 2024 Honda NX 500 delivers 46.9 hp @ 8600 rpm of peak power and 43 Nm @ 6500 rpm of torque. From a practical standpoint, the 2024 NX 500 tips the scales at 198 kg, carries a 17.5-litre fuel tank, offers a seat height of 830 mm and spans a 1445 mm wheelbase. Scroll down for the complete 2024 Honda NX 500 spec sheet covering every technical detail from suspension travel to tyre sizes.
2024 NX 500 - Pros & Cons
Strengths
-
⚡
Strong power output: 2024 Honda NX 500 makes 46.9 hp @ 8600 rpm with 43 Nm @ 6500 rpm of torque - competitive figures for its class.
Considerations
-
📏
Tall seat height: The 830 mm seat height will challenge shorter riders - tiptoeing at low speeds is something to factor into your decision.
-
⚙️
Chain final drive upkeep: Chain final drive needs regular cleaning, lubrication and tension checks to get full life out of the sprockets.
Wear Points & Servicing Notes
Cooling system servicing
The Liquid cooled system on the NX 500 needs a coolant change roughly every two years (or per the service schedule) - skipping it lets the coolant turn acidic and corrode the aluminium water passages over time.
Brake disc and pad wear
The 2x 296mm wave disc with Nissin radial-mount two piston calipers front brake gives strong, progressive stopping power. Disc thickness and pad depth are worth checking at every tyre change, since worn pads can score the disc surface.
Suspension condition on used examples
Up front, the NX 500 runs 41mm Showa SFF-BP USD forks, pre-load adjustable and Prolink mono with 5 stage preload adjuster, steel hollow cross swingarm at the rear. On a used example, check fork seals for weeping oil and test the rear linkage for play - seals are a relatively cheap fix but useful when negotiating price.
Final drive maintenance
Final drive is by chain - expect to clean and lube it every few hundred kilometres and check tension regularly; a neglected chain wears the sprockets faster than the chain itself.
Frame & chassis check
The frame is Steel diamond - worth a visual check for corrosion or impact damage around the head-stock and swingarm pivot on any used example, since frame damage is far costlier to fix than any service item.
NX 500 - Buying & Maintenance Guide
What to check before buying
When inspecting a used 2024 Honda NX 500, start with the basics: check the service book for oil change frequency, inspect the chain and sprockets for wear, and look for oil seepage around the engine casings and rocker covers. A cold start test is invaluable - a well-maintained NX 500 should fire up cleanly and settle to a smooth idle within a few seconds.
Oil and filter changes
Regular oil changes are the single most important maintenance task on any NX 500. Stick to the manufacturer's interval - typically every 6,000 km or once a year, whichever comes first. Always use the correct viscosity grade as specified in the owner's manual.
Carburetor upkeep
Keep the carburetors clean and free of deposits. If the NX 500 has been stored, strip and clean the carb float bowls before attempting to start it. Pilot jets are the first to block and the last to be checked - always include them in any carb rebuild.
2024 Honda NX 500 - Frequently Asked Questions
What engine does the 2024 Honda NX 500 have?
The 2024 Honda NX 500 uses a Four stroke, parallel-twin, DOHC, 4 valves per cylinder engine with 471 cc of displacement. It is liquid cooled.
How much does the 2024 Honda NX 500 weigh?
The 2024 Honda NX 500 weighs 198 kg. This is the manufacturer's wet figure.
How much power does the 2024 Honda NX 500 make?
The 2024 Honda NX 500 produces 46.9 hp @ 8600 rpm of power and 43 Nm @ 6500 rpm of torque. These are peak figures.
What is the fuel tank capacity of the 2024 Honda NX 500?
The 2024 Honda NX 500 has a 17.5-litre fuel tank. At around 5-6 litres per 100 km, that is roughly 291-350 km between stops.
Is the 2024 Honda NX 500 suitable for shorter riders?
The 2024 Honda NX 500 has a seat height of 830 mm. This is towards the tall end of the spectrum and will require most riders under 175 cm to tiptoe at stops.
What brakes does the 2024 Honda NX 500 have?
The 2024 Honda NX 500 uses 2x 296mm wave disc with Nissin radial-mount two piston calipers at the front and Single 240mm wave disc 1 piston calipers at the rear.
What tyre sizes does the 2024 Honda NX 500 use?
The 2024 Honda NX 500 runs 110/80R19M/C front and 160/60R17M/C rear tyres. A good selection of sport, touring and all-weather rubber is available in these sizes.
What gearbox does the 2024 Honda NX 500 have?
The 2024 Honda NX 500 is fitted with a 6 Speed transmission.
Key Specifications
Engine
Four stroke, parallel-twin, DOHC, 4 valves per cylinder
Power
46.9 hp / 35 kW @ 8600 rpm
Torque
43 Nm / 31.7 lb-ft @ 6500 rpm
Top Speed
Not published by manufacturer
Fuel Capacity
17.5 Litres / 4.6 US gal
Advertisement
Full 2024 Honda NX 500 Specifications
Year
2024
Make Model
Honda NX 500
Seat Height
830 mm / 32.7 in
Wheelbase
1445 mm / 56.9 in
Ground Clearance
180 mm / 7.0 in
Height
1415 mm / 55.7 in
Length
2165 mm / 84.8 in
Width
830 mm / 32.6 in
Fuel Capacity
17.5 Litres / 4.6 US gal
Oil Capacity
3.2 Litres
Wet Weight
198 kg / 437 lbs
Displacement
471 cc / 28.7 cu-in
Engine Detail
Four stroke, parallel-twin, DOHC, 4 valves per cylinder
Bore x Stroke
67.0 x 66.8 mm
Compression Ratio
10.7:1
Cooling System
Liquid cooled
Emissions
EURO5
Fuel Induction
PGM-FI with 34mm throttle bodies
Ignition
Computer-controlled digital transistorized with electronic advance
Starter
Electric
Clutch
Wet multiplate, assisted slipper clutch
Final Drive
#520 O-ring sealed chain
Transmission / Drive
6 Speed
Frame Type
Steel diamond
Suspension - Front
41mm Showa SFF-BP USD forks, pre-load adjustable
Suspension - Rear
Prolink mono with 5 stage preload adjuster, steel hollow cross swingarm
Rake
27.5°
Trail
108 mm / 4.25 in
Wheel Travel - Front
150 mm / 5.9 in
Wheel Travel - Rear
135 mm / 5.3 in
Brakes - Front
2x 296mm wave disc with Nissin radial-mount two piston calipers
Brakes - Rear
Single 240mm wave disc 1 piston calipers
ABS
2 Channel system
Rims - Front
19 X MT2.5
Rims - Rear
17 X MT4.5
Tyres - Front
110/80R19M/C (59H)
Tyres - Rear
160/60R17M/C (69H)
Wheels
Multi-spoke cast aluminium
Specifications are compiled from manufacturer documentation and cross-referenced
technical sources, and corrected on an ongoing basis.
Spot an error? Let us know.
Advertisement