![]()
No images available
Tap to enlarge
![]()
2012 Honda CBR 250R Overview
Honda CBR 250R is a sport motorcycle, displacing 249.40 cc. Power comes from a Single cylinder, four-stroke engine running DOHC valve actuation, a compression ratio of 10.7:1. Bore and stroke come in at 76 x 55 mm. On the performance side, it delivers 4 Nm @ 5500 Revolutions of torque. On the road, the 2012 CBR 250R tips the scales at 161.9 kg, carries a 12.87-litre fuel tank, offers a seat height of 775 mm and spans a 1,369 mm wheelbase. That's roughly 32.9 kg lighter than the average sport motorcycle in our database. The full 2012 Honda CBR 250R spec sheet below covers every technical detail, from suspension travel to tyre sizes.
2012 Honda CBR 250R compared with other bikes in the Sport category
We checked the recorded figures for the 2012 Honda CBR 250R against up to 1607 bikes in the Sport category in our database, counting each model once at the model year nearest to this one.
- Only 3 of the other 1572 bikes in the Sport category have a lower torque than the 4 Nm of the CBR 250R.
- With 775 mm, the CBR 250R has the joint 220th lowest seat height of 1607 bikes in the Sport category, 3% below the category average of 803 mm.
- Wet weight of 161.9 kg is lighter than that of 981 of the other 1212 bikes in the Sport category.
- Narrowing the field to the 608 models within five model years of it, the torque of 4 Nm is lower than that of 603 of the other 607.
2012 CBR 250R - Pros & Cons
Strengths
-
🔧
Fuel injection: Fuel injection means consistent cold starts and clean throttle response without the fussiness of a carbureted setup.
-
🛑
Strong front braking: Stopping power up front is strong thanks to the single disc setup, with plenty of room to upgrade further with braided lines.
Considerations
-
⚙️
Chain final drive upkeep: Budget time for routine chain maintenance - it's cheap to replace but needs consistent attention to avoid premature sprocket wear.
Wear Points & Servicing Notes
Fuelling & injector care
The fuel injection on the CBR 250R needs little beyond good fuel and periodic use of an injector-cleaner additive - no jetting or float-bowl maintenance to worry about.
Valve clearance checks
With DOHC valve gear, the CBR 250R needs periodic clearance checks; caught early they're a cheap adjustment, left unchecked they accelerate valve seat wear.
Brake disc and pad wear
Braking up front comes from single disc - solid stopping power, with disc and pad wear best checked on the same schedule as tyre changes.
Suspension condition on used examples
The CBR 250R's suspension runs 37mm fork at the front. The rear uses Pro-Link single shock with five positions of spring preload adjustability. Fork-seal condition and rear linkage play are the two things worth checking before buying used.
Final drive maintenance
The CBR 250R uses chain final drive, which is cheap to replace but needs regular cleaning, lubrication and tension checks to get a full service life out of the sprockets.
CBR 250R - Buying & Maintenance Guide
What to check before buying
Before handing over money for a used 2012 Honda CBR 250R with its 249.40 cc sport, cover the fundamentals: service book and oil change history, drivetrain wear, and any sign of oil weeping around the casings. This model runs chain final drive, so check chain slack and sprocket tooth profile specifically - a worn sprocket is a cheaper fix now than after it's chewed up the next chain. Now 14 years old, this sport is as likely to show age-related wear (perished rubber, seized fasteners, degraded seals) as mileage-related wear. Cold-starting it yourself tells you a lot - a healthy CBR 250R should catch quickly and settle into a smooth idle.
Oil and filter changes
Nothing protects the CBR 250R's 249.40 cc single cylinder, four-stroke like disciplined oil changes - stay on the manufacturer's schedule (roughly every 6,000 km or annually). With a 10.7:1 compression ratio, running the octane grade specified in the manual matters more than on a lower-compression engine. Match the viscosity grade to what the owner's manual specifies, not what's cheapest.
Fuel system care
Fuel injection on the CBR 250R needs little attention beyond decent fuel and an occasional system-cleaner additive. Anything left standing for three months or more should have its fuel drained and replaced before it varnishes the injectors.
Valve clearance service
Valve clearances are easy to overlook on a used CBR 250R since a bike out of spec doesn't always feel obviously wrong - but the wear it causes is real. Ask the seller for documentation before assuming it's been done.
2012 Honda CBR 250R - Frequently Asked Questions
What engine does the 2012 Honda CBR 250R have?
The 2012 Honda CBR 250R uses a Single cylinder, four-stroke engine with 249.40 cc of displacement.
How much does the 2012 Honda CBR 250R weigh?
The 2012 Honda CBR 250R weighs 161.9 kg. This is the manufacturer's wet figure.
How much torque does the 2012 Honda CBR 250R produce?
The 2012 Honda CBR 250R produces 4 Nm @ 5500 Revolutions of torque.
What is the fuel tank capacity of the 2012 Honda CBR 250R?
The 2012 Honda CBR 250R has a 12.87-litre fuel tank. At around 5-6 litres per 100 km, that is roughly 214-257 km between stops.
Is the 2012 Honda CBR 250R suitable for shorter riders?
The 2012 Honda CBR 250R has a seat height of 775 mm. This is a moderate seat height that suits a wide range of rider heights.
What brakes does the 2012 Honda CBR 250R have?
The 2012 Honda CBR 250R uses single disc at the front and single disc at the rear.
What tyre sizes does the 2012 Honda CBR 250R use?
The 2012 Honda CBR 250R runs 110/70-17 front and 140/70-17 rear tyres. A good selection of sport, touring and all-weather rubber is available in these sizes.
Honda CBR 250R Spec Evolution
The Honda CBR 250R was produced across 5 model years (2012-2017). The table below highlights the key specifications that changed across the production run - useful whether you are comparing years or tracking down a specific variant.
| Specification |
2012 |
2014 |
2015 |
2016 |
2017 |
| Max Power |
23.7 hp / 17.7 kW @ 9900 rpm |
26 hp / 19.3 kW @ 8500 rpm |
- |
- |
- |
| Wet Weight |
161.9 kg / 357.0 lbs |
165.0 kg / 363.8 lbs |
165.0 kg / 363.8 lbs |
165.0 kg / 363.8 lbs |
165.0 kg / 363.8 lbs |
| Dry Weight |
310 kg / 683.4 lbs |
138 kg / 304.2 lbs |
- |
- |
- |
| Engine Detail |
Four stroke, single cylinder, DOHC, 4 valve per cylinder. |
Four stroke, single cylinder, DOHC, 4 valve |
- |
- |
- |
| Seat Height |
785 mm / 30.5 in |
775 mm / 30.5 in. |
775 mm / 30.5 in. |
775 mm / 30.5 in. |
775 mm / 30.5 in. |
| Fuel Capacity |
13 Liters / 3.4 gal |
13 Liters / 3.4 gal |
13.00 litres / 3.43 gallons |
13.00 litres / 3.43 gallons |
13.00 litres / 3.43 gallons |
| Fuel Control |
DOHC |
DOHC |
Double Overhead Cams/Twin Cam (DOHC) |
Double Overhead Cams/Twin Cam (DOHC) |
Double Overhead Cams/Twin Cam (DOHC) |
| Comments |
French brand. |
Model ID: CBR250R |
Model ID: CBR250R |
Model ID: CBR250R |
Model ID: CBR250R |
Key Specifications
Engine
Single cylinder, four-stroke
Torque
4.00 Nm (0.4 kgf-m or 3.0 ft.lbs) @ 5500 Revolutions
Weight
161.9 kg / 357.0 lbs
Fuel Capacity
12.87 litres / 3.40 gallons
Advertisement
Full 2012 Honda CBR 250R Specifications
Comments
French brand.
Colours
Metallic Black, Red/Silver, White/Pearl Blue/Red
Seat Height
775 mm / 30.5 in.
Wheelbase
1,369 mm / 53.9 in.
Height
1,150 mm / 45.3 in.
Length
1,810 mm / 71.3 in.
Width
685 mm / 27.0 in.
Dry Weight
310 kg / 683.4 lbs
Fuel Capacity
12.87 litres / 3.40 gallons
Wet Weight
161.9 kg / 357.0 lbs
Displacement (cc)
249.40 cc
Displacement (ci)
15.22 cubic inches
Engine Type
Single cylinder, four-stroke
Fuel Control
DOHC
Bore x Stroke (in,)
3.0 x 2.2 inches
Bore x Stroke (mm)
76.0 x 55.0 mm
CO2
70.8 CO
Fuel System
Injection. PGM-Fi, 38mm throttle body
Compression Ratio
10.7:1
Emissions
Meets current EPA standards. Models sold in California meet current CARB standards and may differ slightly due to emissions equipment.
Fuel Consumption
3.05 litres/100 km (32.8 km/l or 77.12 mpg)
Ignition
Computer-controlled digital transistorized with electronic advance
Starter
Electric
Valve System
4
Final Drive
Chain
Gearbox
6-speed
Primary Drive
CVT
Suspension - Front
37mm fork
Suspension - Rear
Pro-Link single shock with five positions of spring preload adjustability
Rake
25.0°
Seat
Dual
Trail
99 mm / 3.9 in.
Wheel Travel - Front
118 mm / 4.7 in.
Wheel Travel - Rear
103 mm / 4.1 in.
Brakes - Front Diameter (in.)
11.7 inches
Brakes - Front Diameter (mm)
296 mm
Brakes - Rear Diameter (in.)
8.7 inches
Brakes - Rear Diameter (mm)
220 mm
Brakes - Front
Single disc
Brakes - Rear
Single disc
Tyres - Front
110/70-17
Tyres - Rear
140/70-17
Specifications are compiled from manufacturer documentation and cross-referenced
technical sources, and corrected on an ongoing basis.
Spot an error? Let us know.
Advertisement